please dont rip this site

Epson ESC printer commands

(this article is a stub, please help by contributing additional commands or taking ownership of the page and editing it.)

P2 = ESC/P2 command
P = ESC/P command
9P = 9-Pin ESC/P command

ESC = ASCII Escape Character. 27 decimal, 1B hex.

Bolded items are ASCII Text. E.g. U is the ASCII character "U", 55 decimal.
Plain numbers are decimal binary values. E.g. 5 is a single byte with a value of 5 decimal or the ASCII ENQ command.
Plain text are ASCII control code names. E.g. BEL is the ASCII bell command with a value of 7 decimal.
Italic items are parameters which may be replaced with values as indicated in the Description column. multi-byte values are always big endian: The first byte is the least significant value.

Command 		P2 P 9P	Description
BEL     		 · · ·	Beeper. Beep for 1/10 second.
BS      		 · · · 	Backspace. Move cursor left 1 character unless at left margin. Depreciated. See ESC $, ESC \, HT, DEL
HT        		 · · · 	Tab horizontally. Move cursor 1 tab right unless at right margin or no tab defined. No scoring. C-43
LF      		 · · · 	Line feed. Move cursor down line spacing distance and to left margin. Preceed with CR. Cancels SO. C-27
VT      		 · · ·	Tab vertically C-45
FF      		 · · ·	Form feed. Print buffer, eject page, move cursor to top of next page at left margin C-29
CR       		 · · ·	Carriage return Move cursor to left margin. required after each line of text or graphics. C-25
SO       		 · · ·	Select double-width printing (one line) · · · C-140
SI       		 · · ·	Select condensed printing · · · C-134
DC1       		 · · ·	Select printer · · · C-204
DC2       		 · · ·	Cancel condensed printing · · · C-138
DC3       		 · · ·	Deselect printer · · · C-206
DC4       		 · · ·	Cancel double-width printing (one line) · · · C-144
CAN       		 · · ·	Cancel line · · · C-200
ESC 1			 — — ·	End IEEE 1284.4 protocol. Used at start of print file. (that is ESC 0x01, not ESC "1")
ESC 19	m			?	m is typically 31
ESC SO  		 · · ·	Select double-width printing (one line) · · · C-142
ESC SI  		 · · ·	Select condensed printing · · · C-136
ESC EM  		 · · ·	Control paper loading/ejecting · · · C-157
ESC SP n 		 · · ·	Set intercharacter space to n/180 in LQ or n/120 in draft. 0 to 127. C-108
ESC ! n  		 · · ·	Master select n=(12cpi?/10cpi)+2*(proportional?)+4*(condensed?)+8*(bold?)+16*(dstrike?)+32*(dwidth?)+64*(italic?)+128*(underline?) C-118
ESC #   		 · · ·	Cancel MSB control set via ESC = or ESC > C-208
ESC $   		 · · ·	Set absolute horizontal print position · · · C-31
ESC %   		 · · ·	Select user-defined set · · · C-91
ESC &   		 · · ·	Define user-defined characters · · · C-84
ESC ( -   		 · · —	Select line/score C-127
ESC ( $ 4 0 nnnn		Advance n horizontal units.
ESC ( B   		 · · ·	Bar code setup and print · · · C-195
ESC ( C 2 0 mm  	 · — —	Set page length in defined unit (see: Set Unit). (page length) = (m)*(defined unit), Clears top and bottom margin.
ESC ( C 4 0 mmmm	 · — —	Set page length in defined unit (see: Set Unit). (page length) = (m)*(defined unit), Clears top and bottom margin.
ESC ( D 4 0 bb V H      	Set dot spacing. Vertical=V/b Horizontal=H/b. b is always 1440.
ESC ( G 1 0 m       	 · — —	Select graphics mode on m=1, off m=0. Most jobs are entirely graphics. C-169
ESC ( K 2 0 0 m         	Set Color/Grey. m=0 (color), 1 (grey), or 2 (color) (? difference between 0 and 2)
ESC ( R l1 l2			Send Remote command of length=l1*256+l1. Known remote commands:
  T I 8 0 YYY M D H M S 	Timestamp Information. Year=Y3*65535+Y2*256+Y1. Month=M, Day=D, Hour(24 hour format)=H, etc...
  J S 8 0 0 1 J ? ? ? 64	Job Header. J counts the number of jobs since OS restart.
  J H 
  P M
  D P
  S N
  M I 4 0 0 1 mm        	Media Information plain=0,inkjet=1,Premium=3,Postcard=5,Photo=6,GlossyFilm=7,Transparency/Envelope=9,BackLightFilm=10,etc...
  U S
  F P
  P P 3 0 ddd            	Paper Path (tray select): Rear=0 1 0, Main=0 1 1, Photo=0 1 2, Standard=0 1 255, Manual=0 2 0, CD=0 2 1, SheetGuide=0 3 0, RollFeed=0 3 1
  L D
  J E
ESC 0 0 0 0			Exit Remote command.
ESC ( S 8 0 ww ll		Set sheet Width=w and Height=h in PageUnits.
ESC ( U 5 0 P V H BB	 · — —	Set units BaseUnits = 1/B inch. PageUnit=P*(BaseUnits). VerticalUnits=V*(BaseUnits). HorizontalUnits=H*(BaseUnits) C-50 Does not change setting previously set with other commands which reference this unit.
ESC ( V         	 · — —	Set absolute vertical print position · — — C-37
ESC ( ^         	 · — —	Print data as characters · — — C-150
ESC ( c 8 0 tttt llll 	 · — —	Set page format TopMargin=t and ImageLength=l in PageUnits · — — C-11
ESC ( e 2 0 0 d     		Set DotSize=d in unknown units.
ESC ( i 1 0 m        	 · — —	Select MicroWeaveMode=m 0-Off, 1-FullOverlap, 2-FourPass, 3-FullOverLapFourPass · — — C-171
ESC ( t         	 · — —	Assign character table · — · C-73
ESC ( v 4 0 aaaa      	 · — —	Advance vertical print position a VerticalUnits· — — C-39
ESC *                 	 · · ·	Select bit image · · · C-177
ESC +                 	 · · —	Set n/360-inch line spacing · · — C-57
ESC -                 	 · · ·	Turn underline on/off · · · C-125
ESC .                 	 · — —	Print raster graphics · — — C-172
ESC . 2         	 · — —	Enter TIFF compressed mode · — — C-175
ESC /           	 — · ·	Select vertical tab channel — · · C-67
ESC 0            	 · · ·	Select 1/8-inch line spacing · · · C-51
ESC 1            	 — — ·	Select 7/72-inch line spacing — — · C-60
ESC 2            	 · · ·	Select 1/6-inch line spacing · · · C-53
ESC 3            	 · · —	Set n/180-inch line spacing · · — C-55
ESC 3            	 — — ·	Set n/216-inch line spacing — — · C-56
ESC 4            	 · · ·	Select italic font · · · C-114
ESC 5            	 · · ·	Cancel italic font · · · C-116
ESC 6            	 · · ·	Enable printing of upper control codes · · · C-151
ESC 7            	 · · ·	Enable upper control codes · · · C-153
ESC 8            	 — — ·	Disable paper-out detector — — · C-165
ESC 9            	 — — ·	Enable paper-out detector — — · C-166
ESC :            	 · · ·	Copy ROM to RAM · · · C-89
ESC <            	 · · ·	Unidirectional mode (one line) · · · C-161
ESC =            	 · · ·	Set MSB to 0 · · · C-210
ESC >            	 · · ·	Set MSB to 1 · · · C-212
ESC ?            	 · · ·	Reassign bit-image mode · · · C-181
ESC @              	 · · ·	Reset. dump buffered data, eject any partly printed page, return all settings to default. Should start each page.
ESC A              	 · · —	Set n/60-inch line spacing · · — C-58
ESC A              	 — — ·	Set n/72-inch line spacing — — · C-59
ESC B              	 · · ·	Set vertical tabs · · · C-63
ESC C              	 · · ·	Set page length in lines · · · C-13
ESC C              	 · · ·	NUL Set page length in inches · · · C-15
ESC D              	 · · ·	Set horizontal tabs · · · C-61
ESC E              	 · · ·	Select bold font · · · C-110
ESC F              	 · · ·	Cancel bold font · · · C-112
ESC G              	 · · ·	Select double-strike printing · · · C-121
ESC H              	 · · ·	Cancel double-strike printing · · · C-123
ESC I              	 — — ·	Enable printing of control codes — — · C-155
ESC J              	 · · ·	Advance print position vertically · · · C-41
ESC K              	 · · ·	Select 60-dpi graphics · · · C-183
ESC L              	 · · ·	Select 120-dpi graphics · · · C-185
ESC M              	 · · —	Select 10.5-point, 12-cpi · · — C-102
ESC M              	 — — ·	Select 12-cpi — — · C-103
ESC N              	 · · ·	Set bottom margin · · · C-17
ESC O              	 · · ·	Cancel bottom margin · · · C-19
ESC P              	 · · —	Select 10.5-point, 10-cpi · · — C-100
ESC P              	 — — ·	Select 10-cpi — — · C-101
ESC Q              	 · · ·	Set right margin · · · C-21
ESC R              	 · · ·	Select an international character set · · · C-80
ESC S              	 · · ·	Select superscript/subscript printing · · · C-129
ESC T              	 · · ·	Cancel superscript/subscript printing · · · C-131
ESC U m               	   	Set print direction Bi m=0, uni m=1
ESC W              	 · · ·	Turn double-width printing on/off · · · C-146
ESC X              	 · — —	Select font by pitch and point · — — C-97
ESC Y              	 · · ·	Select 120-dpi, double-speed graphics · · · C-187
ESC Z              	 · · ·	Select 240-dpi graphics · · · C-189
ESC \              	 · · ·	Set relative horizontal print position · · · C-33
ESC ^              	 — — ·	Select 60/120-dpi, 9-pin graphics — — · C-191
ESC a              	 — · ·	Select justification — · · C-71
ESC b              	 — · ·	Set vertical tabs in VFU channels — · · C-65
ESC c              	 · — —	Set horizontal motion index (HMI) · — — C-99
ESC e              	 — — ·	Set fixed tab increment — — · C-69
ESC f              	 — — ·	Horizontal/vertical skip — — · C-47
ESC g              	 · · —	Select 10.5-point, 15-cpi · · — C-104
ESC g              	 — — ·	Select 15-cpi — — · C-105
ESC i C F b BB RR D. 13	 — — ·	Immediate mode image data Color Format(0=raw,1=TIFFRLE,2=?) bits/pixel BytesTotal Rows Data C-215
ESC j              	 — — ·	Reverse paper feed — — · C-214
ESC k              	 · · ·	Select typeface · · · C-95
ESC l              	 · · ·	Set left margin · · · C-23
ESC m              	 — — ·	Select printing of upper control codes — — · C-156
ESC p              	 · · ·	Turn proportional mode on/off · · · C-106
ESC q              	 · · —	Select character style · · — C-133
ESC r              	 · · ·	Select printing color · · · C-193
ESC s              	 · · ·	Select low-speed mode · · C-167
ESC t              	 · · ·	Select character table · · · C-77
ESC w              	 · · ·	Turn double-height printing on/off C-148
ESC x              	 · · —	Select LQ or draft C-93
ESC x              	 — — ·	Select NLQ or draft C-94
DEL              	 · · ·	Delete last character in buffer C-202

See also:


file: /Techref/language/ESC/commands.htm, 14KB, , updated: 2011/5/24 16:08, local time: 2024/12/23 02:41,
TOP NEW HELP FIND: 
3.137.181.194:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://massmind.ecomorder.com/Techref/language/ESC/commands.htm"> Epson ESC printer commands</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

 

Welcome to ecomorder.com!

 

Welcome to massmind.ecomorder.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .