;----------------------------------------------------------------------;
; COMBO4M.ASM A combination lock 4 Mhz ;
;----------------------------------------------------------------------;
; Hold both buttons down when power applied to enter code set routine
; A total of 8 button presses makes up the combination. If the correct
; combination is entered, all four LEDs will flash 6 times else once.
; .-----------.
; -|RA2 RA1|- V+ = 4.5 or 5V
; -|RA3 RA0|- X = 4 MHz cer. res.
; -|RA4 OSC1|--|X|___ gnd
; -{r}- = 470 ohm V+ ---|MCLR OSC2|--|X|
; -|<- = LED gnd ---|Vss Vdd|--- V+
; gnd ---|<--{r}--|RB0 RB7|-
; gnd ---|<--{r}--|RB1 RB6|-
; gnd ---|<--{r}--|RB2 RB5|---[PB]--- gnd
; gnd ---|<--{r}--|RB3 RB4|---[PB]--- gnd
; '-----------'
; PIC16F84 -[PB]- pushbutton
LIST P=16F84 ; tells which processor is used
INCLUDE "p16f84.inc" ; defines various registers etc. Look
ERRORLEVEL -224 ; supress annoying message from tris
ERRORLEVEL -302 ; " " " page change
__CONFIG _PWRTE_ON & _XT_OSC & _WDT_OFF ; config.switches
#define PB1 PORTB, 4 ; Pushbutton #1, generates a '0' bit
#define PB2 PORTB, 5 ; Pushbutton #2, generates a '1' bit
#define LED1 PORTB, 3 ; LED #1
#define LED2 PORTB, 0 ; LED #2
; register usage:
CBLOCK H'C'
combo ; holds combination
count ; general count register
codevalue ; holds code value
cntmsec ; used to count milliseconds
ENDC
ORG 0 ; start a program memory location zero
goto main ; jump over the interrupt routine
;----------------------------------------------------------------------;
; Initialize the ports etc. ;
;----------------------------------------------------------------------;
init: movlw B'00000000' ; all bits low in W
tris PORTA ; contents of W copied to PORT A ...
movlw B'00110000' ; Rb4,RB5 inputs, all other output
tris PORTB ; into PORT B
clrf PORTB ; LEDs blanked
movlw 0
option ; Port B pullups enabled
return
;----------------------------------------------------------------------;
; Read a byte from the data EEPROM at address given in W ;
;----------------------------------------------------------------------;
readee movwf EEADR ; set up eeprom address from W
bsf STATUS,RP0 ; change to page 1
bsf EECON1,RD ; set the read bit
bcf STATUS,RP0 ; back to page 0
movf EEDATA,W ; return value in W
return
;----------------------------------------------------------------------;
; This routine writes a byte to data EEPROM ;
; set up EEADR and EEDATA before entry ;
;----------------------------------------------------------------------;
writee: bsf STATUS,RP0 ; enter page 1
clrf EECON1
bsf EECON1,WREN ; enable write
movlw H'55' ; magic sequence
movwf EECON2
movlw H'AA'
movwf EECON2
bsf EECON1,WR
eeloop: btfsc EECON1,WR ; wait for WR to go low
goto eeloop ; not yet
bsf EECON1,WREN
bcf EECON1,EEIF ; clear the interrupt flag
bcf STATUS,RP0 ; return to page 0
movlw D'10' ; delay to 'burn' in
call nmsec
return
;----------------------------------------------------------------------;
; Enter Code ;
;----------------------------------------------------------------------;
entercode:
movlw 1 ; flash once
call flashleds
movlw 8 ; set up to count 8 presses
movwf count
waitboth:
btfss PB1 ; wait until pushbutton 1 up
goto waitboth
btfss PB2 ; and pushbutton 2 up
goto waitboth
call msec20 ; bypass any bouncing
bcf LED1
bcf LED2
eitherbutton: ; wait until either button pressed
comf PORTB, W ; compliment of Port B in W
andlw B'00110000' ; look at buttons, ( 0's if up)
btfsc STATUS, Z ; skip if either pressed
goto eitherbutton ; try again
call msec20 ; debounce press (not in 32 kHz ver)
bcf STATUS, C ; clear carry
btfss PB1 ; if one pressed leave carry clear
goto PB1pressed
bsf STATUS, C ; else set carry
goto $ + 3 ; skip over
PB1pressed bsf LED1 ; turn LED1 on
goto $ + 2 ; skip over
bsf LED2 ; turn LED2 on
rrf combo, f ; roll result into combo high bit
decfsz count, f ; more presses necessary
goto waitboth ; next press
movf combo, W ; transfer result to W
return
;----------------------------------------------------------------------;
; time delay routines ;
;----------------------------------------------------------------------;
micro4 addlw H'FF' ; subtract 1 from 'W'
btfss STATUS,Z ; skip when you reach zero
goto micro4 ; more loops
return
onesecond: ; a subroutine that delays for 1 sec
call msec250
call msec250
call msec250
call msec250
return
msec20 movlw D'20' ; 20 msec delay entry point
goto nmsec
msec250: ; a subroutine to delay 250 msec
movlw D'250'
;*** N millisecond delay routine ***
nmsec: movwf cntmsec ; delay for N (in W) millisec
msecloop: movlw D'248' ; 1 usec for load
call micro4 ; this instruction is 995 usec
nop ; 1 usec
decfsz cntmsec,f ; 1 usec, (2 if skip taken)
goto msecloop ; 2 usec, loop = 995+5 = 1 msec
return
;----------------------------------------------------------------------;
; Flash the LEDs, number of flashes in W on entry ;
;----------------------------------------------------------------------;
flashleds:
movwf count
flashloop:
movlw H'F'
movwf PORTB
call onesecond + 2 ; 1/2 sec on
movlw 0
movwf PORTB
call onesecond + 2 ; 1/2 sec off
decfsz count, f
goto flashloop
return
;----------------------------------------------------------------------;
; Get combo value and place it in EEPROM location 0 ;
;----------------------------------------------------------------------;
setcombo:
call entercode ; get desired press combination
movwf EEDATA ; set up data and address
movlw 0
movwf EEADR
call writee ; save combo in EEPROM
movlw 2 ; flash leds 2 times
call flashleds ; (one additional when entering main)
return
;----------------------------------------------------------------------;
; The Main routine ;
;----------------------------------------------------------------------;
main:
call init ; initialize registers etc.
movf PORTB, W ; check both buttons pressed on pwr-up
andlw B'00110000' ; look at buttons, (0's if down)
btfsc STATUS, Z ; skip if both not presssed
call setcombo ; if both press set the combination
movlw 0 ; get combo from EEPROM address 0
call readee
movwf codevalue ; save it
mainloop:
call entercode
subwf codevalue, W ; is it same as code?
btfss STATUS, Z ; zero set if yes
goto mainloop
movlw 5 ; sucess, unlocking procedure would ...
call flashleds ; be placed here.
goto mainloop
org 2100 ; this is location of EEPROM data
dw H'33' ; the initial value of location 0 ...
; is set to B'00110011'
end ; end of program
| file: /Techref/piclist/cheapic/combo4m.asm, 9KB, , updated: 2000/12/7 15:55, local time: 2024/11/14 23:54,
3.148.107.34:LOG IN
|
| ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://massmind.ecomorder.com/techref/piclist/cheapic/combo4m.asm"> piclist cheapic combo4m</A> |
| Did you find what you needed? |
Welcome to ecomorder.com! |
Welcome to massmind.ecomorder.com! |
.