please dont rip this site Prev Next

GetTapeParameters info  Overview  Group

The GetTapeParameters function retrieves information that describes the tape or the tape drive.

DWORD GetTapeParameters(

    HANDLE hDevice,

// handle of open device

    DWORD dwOperation,

// type of information requested

    LPDWORD lpdwSize,

// address of returned information

    LPVOID lpTapeInformation 

// tape media or drive information

   );

Parameters

hDevice
Identifies the device about which information is sought. This handle is created by using the CreateFile function.
dwOperation
Specifies the type of information requested. This parameter must be one of the following values:

Value

Description

GET_TAPE_MEDIA_INFORMATION

Retrieves information about the tape in the tape device.

GET_TAPE_DRIVE_INFORMATION

Retrieves information about the tape device.

lpdwSize
Points to a variable that receives the size, in bytes, of the buffer specified by the lpTapeInformation parameter. If the buffer is too small, this parameter receives the required size.
lpTapeInformation
Points to a structure that contains the requested information. If the dwOperation parameter is GET_TAPE_MEDIA_INFORMATION, lpTapeInformation points to a TAPE_GET_MEDIA_PARAMETERS structure.

If dwOperation is GET_TAPE_DRIVE_INFORMATION, lpTapeInformation points to a TAPE_GET_DRIVE_PARAMETERS structure.

Return Values

If the function succeeds, the return value is NO_ERROR.

If the function fails, the return value is one of the following error codes:

Error code

Description

ERROR_BEGINNING_OF_MEDIA

An attempt to access data before the beginning-of-medium marker failed.

ERROR_BUS_RESET

A reset condition was detected on the bus.

ERROR_END_OF_MEDIA

The end-of-tape marker was reached during an operation.

ERROR_FILEMARK_DETECTED

A filemark was reached during an operation.

ERROR_SETMARK_DETECTED

A setmark was reached during an operation.

ERROR_NO_DATA_DETECTED

The end-of-data marker was reached during an operation.

ERROR_PARTITION_FAILURE

The tape could not be partitioned.

ERROR_INVALID_BLOCK_LENGTH

The block size is incorrect on a new tape in a multivolume partition.

ERROR_DEVICE_NOT_PARTITIONED

The partition information could not be found when a tape was being loaded.

ERROR_MEDIA_CHANGED

The tape that was in the drive has been replaced or removed.

ERROR_NO_MEDIA_IN_DRIVE

There is no media in the drive.

ERROR_NOT_SUPPORTED

The tape driver does not support a requested function.

ERROR_UNABLE_TO_LOCK_MEDIA

An attempt to lock the ejection mechanism failed.

ERROR_UNABLE_TO_UNLOAD_MEDIA

An attempt to unload the tape failed.

ERROR_WRITE_PROTECT

The media is write protected.

Remarks

The block size range values (maximum and minimum) returned by the GetTapeParameters function called with the dwOperation parameter set to the GET_TAPE_DRIVE_INFORMATION value will indicate system limits, not drive limits. However, it is the tape drive device and the media present in the drive that determine the true block size limits. Thus, an application may not be able to set all the block sizes mentioned in the range obtained by specifying GET_TAPE_DRIVE_INFORMATION in dwOperation.

See Also

CreateFile, SetTapeParameters, TAPE_GET_DRIVE_PARAMETERS, TAPE_GET_MEDIA_PARAMETERS


file: /Techref/os/win/api/win32/func/src/f40_12.htm, 7KB, , updated: 2000/4/7 11:19, local time: 2024/12/22 23:19,
TOP NEW HELP FIND: 
52.15.233.83:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://massmind.ecomorder.com/Techref/os/win/api/win32/func/src/f40_12.htm"> GetTapeParameters</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

 

Welcome to ecomorder.com!

 

Welcome to massmind.ecomorder.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .