please dont rip this site Prev Next

GetTapePosition info  Overview  Group

The GetTapePosition function retrieves the current address of the tape, in logical or absolute blocks.

DWORD GetTapePosition(

    HANDLE hDevice,

// handle of open device

    DWORD dwPositionType,

// type of address to obtain

    LPDWORD lpdwPartition,

// address of current tape partition

    LPDWORD lpdwOffsetLow,

// address of low-order 32 bits of tape position

    LPDWORD lpdwOffsetHigh 

// address of high-order 32 bits of tape position

   );

Parameters

hDevice
Identifies the device on which to get the tape position. This handle is created by using CreateFile.
dwPositionType
Specifies the type of address to obtain. This parameter can be one of the following values:

Value

Description

TAPE_ABSOLUTE_POSITION

The lpdwOffsetLow and lpdwOffsetHigh parameters receive the device-specific block address. The dwPartition parameter receives zero.

TAPE_LOGICAL_POSITION

The lpdwOffsetLow and lpdwOffsetHigh parameters receive the logical block address. The dwPartition parameter receives the logical tape partition.

lpdwPartition
Points to a variable that receives the number of the current tape partition. Partitions are numbered logically from 1 through n, where 1 is the first partition on the tape and n is the last. When a device-specific block address is retrieved, or if the device supports only one partition, this parameter receives zero.
lpdwOffsetLow
Points to a variable that receives the low-order 32 bits of the current tape position.
lpdwOffsetHigh
Points to a variable that receives the high-order 32 bits of the current tape position. This parameter can be NULL if the high-order 32 bits are not required.

Return Values

If the function succeeds, the return value is NO_ERROR.

If the function fails, the return value is one of the following error codes:

Error code

Description

ERROR_BEGINNING_OF_MEDIA

An attempt to access data before the beginning-of-medium marker failed.

ERROR_BUS_RESET

A reset condition was detected on the bus.

ERROR_END_OF_MEDIA

The end-of-tape marker was reached during an operation.

ERROR_FILEMARK_DETECTED

A filemark was reached during an operation.

ERROR_SETMARK_DETECTED

A setmark was reached during an operation.

ERROR_NO_DATA_DETECTED

The end-of-data marker was reached during an operation.

ERROR_PARTITION_FAILURE

The tape could not be partitioned.

ERROR_INVALID_BLOCK_LENGTH

The block size is incorrect on a new tape in a multivolume partition.

ERROR_DEVICE_NOT_PARTITIONED

The partition information could not be found when a tape was being loaded.

ERROR_MEDIA_CHANGED

The tape that was in the drive has been replaced or removed.

ERROR_NO_MEDIA_IN_DRIVE

There is no media in the drive.

ERROR_NOT_SUPPORTED

The tape driver does not support a requested function.

ERROR_UNABLE_TO_LOCK_MEDIA

An attempt to lock the ejection mechanism failed.

ERROR_UNABLE_TO_UNLOAD_MEDIA

An attempt to unload the tape failed.

ERROR_WRITE_PROTECT

The media is write protected.

Remarks

A logical block address is relative to a partition. The first logical block address on each partition is zero.

Call the GetTapeParameters function to obtain information about the status, capabilities, and capacities of tape drives and media.

See Also

CreateFile, GetTapeParameters, SetTapePosition 


file: /Techref/os/win/api/win32/func/src/f40_13.htm, 7KB, , updated: 2000/4/7 11:19, local time: 2024/12/23 03:39,
TOP NEW HELP FIND: 
3.147.82.108:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://massmind.ecomorder.com/Techref/os/win/api/win32/func/src/f40_13.htm"> GetTapePosition</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

 

Welcome to ecomorder.com!

 

Welcome to massmind.ecomorder.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .